New Kamco Water Treatment Range

Kamco have recently released an update to their range of water treatments.

New concentrate sizes, new products and new certification and a new, very low price.

Here are the top 4 products –

 

SYSTEMSAFE-DM InhibitorSystemsafe-DM Concentrate 500ml pack

NEW 500ml CONCENTRATE now available

SCALE & CORROSION INHIBITOR FOR ALL SYSTEMS

Once a heating system has been power flushed to remove sludge and corrosion deposits, it is important to protect it from further deterioration.

This can be achieved by treating the system water with SYSTEMSAFE-DM, a balanced blend of corrosion and scale inhibitors, formulated to provide complete protection against system corrosion and scale formation.

It gives long term protection to central heating systems, preventing internal corrosion, scale deposition and boiler noises, and extends the life of the system and maintains its operational efficiency.

The formation of black iron oxide sludge, which accumulates in low flow areas to give flow problems and cold spots on radiators, is prevented, as is the electrolytic and oxidic corrosion which leads to localised pin-hole corrosion and leaks.

SYSTEMSAFE-DM may be used with all metals commonly used in heating systems, including iron, steel, brass, copper and aluminium. It is simply added to the heating system and requires no further action.

Certificatest

SYSTEMSAFE-DM has passed the Buildcert/DWTA performance test and approval process, so you can be sure that it will give long term scale and corrosion protection to heating systems.

 

 

HYPER-FLUSHHyper-Flush Concentrate 500ml pack

NEW 500ml CONCENTRATE now available

EXTRA POWER, NON-ACID FLUSHING CHEMICAL FOR USE WITH SYSTEM CIRCULATOR PUMPS, OR WITH A POWER FLUSHING PUMP

FOR USE ON DOMESTIC OR COMMERCIAL SYSTEMS.

HYPER-FLUSH is the non-acid flushing liquid with extra solvency power to take debris into suspension for easy removal by power flushing. It penetrates, loosens and dissolves rust, sludge, corrosion and light scale deposits during normal operation of the system, without formation of particulate matter to cause blockages and damage pumps. HYPER-FLUSH is non-corrosive and works at a near neutral pH, enabling it to be used on older systems showing signs of severe neglect, or which may be in too poor a condition for use of Power Flush FX2 liquid.

HYPER-FLUSH should also be used on systems which have aluminium radiators, or boilers with aluminium heat exchangers. It may be used with all metals commonly used in heating systems and does not cause deterioration of non-metallic components.

HYPER-FLUSH can even loosen complete blockages and is therefore also an excellent pre-treatment for systems with radiators having no flow as a result of heavy sludge build up. There is no “gassing” during cleaning, and no need to bleed radiators during the process. Self neutralising and passivating properties remove the need for further flushing procedures after use, and metal surfaces are left clean and corrosion free.

 

SYSTEM PRE-CLEANSystem Pre-Clean Concentrate 500ml pack

NEW 500ml CONCENTRATE now available

PRE-COMMISSION CLEANSER FOR NEW SYSTEMS

New and modified heating systems often contain installation debris and residues of solder fluxes, jointing compounds, copper swarf, oil, grease and even casting sand from within boiler heat exchangers.

These undesirable contaminants are often the cause of serious problems within the heating system, but a hot water flush of a heating systems without an effective pre-commission cleaner is unlikely to neutralise and remove them, leading to future heating problems.

Pre-commission cleaning with SYSTEM PRE-CLEAN prevents corrosion and contaminant related problems, and conditions and prepares metallic surfaces for maximum protection by SYSTEMSAFE-DM.

SYSTEM PRE-CLEAN disperses and mobilises dirt and contaminants for effective removal by power flushing, passivates multi-metal surfaces, removes grease and oil fouling and neutralises corrosive flux residues.

SYSTEM PRE-CLEAN may be used with all metals commonly used in heating systems, including ferrous metals, brass, copper, aluminium and galvanised steel.

The near neutral properties of SYSTEM PRE-CLEAN remove the need for neutralising procedures after use.

 

SYSTEM-HUSHSystem-Hush Concentrate 500ml pack

NEW 500ml CONCENTRATE now available

ON-LINE DESCALER TO SILENCE BOILER NOISE

Some heating systems can be susceptible to noise problems as a result of baked-on corrosion and limescale deposits on boiler heat exchangers.

Whilst power flushing may cure this, on some systems it may be an ongoing problem. The addition of one litre of SYSTEM-HUSH, together with SYSTEMSAFE-DM, is recommended to cleanse the heat exchanger during normal system operation. SYSTEM-HUSH may be left in the system without draining.

SYSTEM-HUSH works at a near neutral pH, taking rust, corrosion and light scale deposits into solution, without formation of particulate matter to cause blockages and damage pumps. Boiler heat transfer surfaces are left clean, restoring efficiency, and boiler noises are eliminated.

SYSTEM-HUSH may be used with all metals commonly used in heating systems, including ferrous metals, brass, copper, aluminium and galvanised steel. It does not cause deterioration of metallic or non-metallic components when used as recommended, enabling it to be used on older systems which may be in too poor a condition for aggressive descaling chemicals.

The self-neutralising and passivating properties of SYSTEM-HUSH remove the need for time consuming flushing procedures after use, and metal surfaces are left clean and corrosion free.


 

All are available NOW from the shop.

All the best

Paul

No comments yet.

Leave a Reply